Cooler master hyper 212 evo install lifts up

#Cooler master hyper 212 evo install lifts up full
#Cooler master hyper 212 evo install lifts up trial

I remembered that in a few months later Noctua took the crown as top performing air cooled heatsink. Other charts count as well when making a final decision.Д«unnywannyI been using a Prolimatech Megahalems since its introduction back in 2009. Ideally, the lower the ratio, the more efficient a cpu cooler is.

Panteck PH-TC14PE weighs 970g without fans, performing at 46c.Д¬M Hyper 212 EVO Weighs 580g with fan, performing at 51c.

#Cooler master hyper 212 evo install lifts up full

Noctua NH-D14 weighs 900g without fans and it did 45c at full load. To heatsink manufactures: Do something innovating if a wall seems to be in the way! Just look at PSU manufactures, they are reaching 92% Platinum rating, from 82% rating four years ago. Not just slab more metal to defeat the other guy. Could you guys do a heatsink Weight/cooling efficiency chart? This is to make readers see which manufacture did its engineering mission to make a much more effective unit than its competition. It is nice that new cpu heatsinks are becoming better in performance, but i don't like the fact that they are becoming bigger and heavier than previous cpu heatsink kings by only earning a degree or two above the rest. This overhang, coupled with the height of the cooler did prevent us from installing our tall, Corsair Dominator Platinum memory into that slot, however the other 3 slots are unaffected, and there is enough room to get a lower profile RAM stick like our Corsair LPX into the slot nearest the CPU socket, then install the fan afterwards.ДЄs you can see despite the relatively low mounting pressure we observed, the mate between the Hyper 212 EvoвЂ™s direct heatpipes and our processor was fantastic.I been using a Prolimatech Megahalems since its introduction back in 2009. After the fan is in place, it ever so slightly hangs over the DIMM slot nearest to the CPU socket. Ram compatibility may be an issue with the Hyper 212 Evo. The final step comes with mounting the fan to the cooler by simply snapping it into place using the вЂњQuick-SnapвЂќ brackets, and connecting the 4-pin PWM wire to the motherboards CPU fan header. Even fully tightened the cooler was able to twist quite easily on the CPU, how this may affect performance is yet to be seen. Once the screws are started simply tighten them in an alternating pattern until they bottom out. Either you will need to reach around the motherboard and support the backplate, or use a good deal of force to compress the springs on the captive screws in order to get them started.

Once again, if your backplate is not adhered to the motherboard, the slack can make it difficult to get the screw started into the mounting posts. Thermal PasteДЄfter that apply thermal paste to the CPU, place the baseplate onto the CPU and evenly tighten the four phllips head screws that are held captive on the X-Brace. It into position was the method easiest for us. Opening the X-BraceД¬ompletely, slipping it in between the heatpipes, and then collapsing That is designed to keep the X-Brace aligned. Top of the baseplate, as well as a pin on the top of the baseplate Is a post on the bottom of the X Brace that fits into a dimple in the Fortunately, the instructions provided on Cooler Masters

The cooler, and holding it up to the CPU to see if the mounting holesДЄre aligned.

#Cooler master hyper 212 evo install lifts up trial

Is more trial and error of placing the X-Brace on the baseplate of Little lacking here, and getting the brace into the correct position The printed instructions included with the AM4 mounting kit are a Is positioning the X-Brace onto the base of the cooler.

This will be significantly easier if the backplate is adhered to your AM4 motherboard, otherwise an extra hand is useful, or as we do, lie the case down and with 1 hand support the backplate on the back of the motherboard, while attaching the mounting posts with the other.ДЄnother thing of note, if your backplate is not adhered to the motherboard, the backplate will remain loose after the mounting posts have been fully tightened, we would love to see the inclusion of different mounting posts, or even some washers to prevent this. First the stock cooler mounts are removed from the backplate by removing the four phillips head screws, then the mounting posts included with the AM4 installation kit are screwed into the backplate. The Hyper 212 Evo uses the stock AM4 backplate, but not the stock cooler mounts. Were charged $14 shipping for it, which is significant compared to To get the AM4 mounting kit, which consists of a different X-BraceДЄnd 4 mounting posts. Support, the fine print stated you will need to contact Cooler Master Thing of note is that while the Hyper 212 Evo is listed as having AM4